Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Before
After
Before
After
Before
AfterClopay Torsion Spring Replacement: The Dallas Owner’s Guide
We stock and install Clopay-compatible torsion springs across Dallas, with most replacements running $180-$340 installed and completed same-day. You’ll usually discover the failure the hard way: a bang from the garage that sounds like a car backfiring, followed by a door that won’t lift more than a few inches. If you’re standing in the driveway staring at a two-inch gap above the spring, that’s the classic Clopay torsion failure picture.
We’re an independent service provider, not affiliated with Clopay. That means we match the spring to your door’s actual weight and cycle rating, using the measurements stamped on the old spring or measured on site. What you get is a documented replacement with a written price before any work starts.
Key takeaways:
- Installed Clopay torsion spring replacement in Dallas runs $180-$340.
- Same-day availability, springs stocked on the truck.
- Written flat price and scope before we touch anything, per Clause 1 of The Haven Standard.
- Photo record of the failed spring and the new one, included on every visit.
- 365-Day Done Right Promise on the work.
Which Clopay Models This Applies To
Torsion spring replacement follows the same diagnostic path whether your door is a Clopay Classic, a Gallery series, a Coachman, or one of the newer Canyon Ridge models. What changes is spring size, wire gauge, and cycle rating. Clopay specifies torsion springs by inside diameter (typically 1-3/4″ or 2″), wire diameter, length, and wind direction (left or right). The right spring isn’t a guess: it’s a calculation based on door weight, drum size, and height.
Here’s the compatibility gotcha Dallas homeowners hit most often: a Clopay door that came with a specific spring spec from the factory won’t necessarily be the right replacement spec a decade later if the door has gained weight or the drums were changed during a prior repair. The painted color code on the spring cone helps, but color alone isn’t enough. We measure the wire diameter with a caliper before we quote, because matching the wrong spring rate means the door balances poorly and the new spring fails early. If you’re weighing OEM Clopay springs against quality aftermarket equivalents, the honest answer is that a correctly spec’d aftermarket spring from a reputable manufacturer (we install springs rated to match your cycle count) will perform as well as OEM for most residential doors. We stock a full range on the truck, and if your door needs something unusual, we’ll bring it back the same day.
Signs Your Clopay Torsion Spring Replacement Is Failing
- A loud bang from the garage, like a car backfiring. That’s the sound of a torsion spring snapping under tension. It’s not subtle, and it happens when the spring reaches the end of its cycle life, usually at the moment the door is up or down and the spring is under full load. The door will stop lifting normally immediately after.
- The door lifts a few inches and stops, or won’t stay up. With one spring broken, the opener motor is now fighting the full weight of the door. It either won’t move it at all or it heaves it a few inches before stalling. The remaining spring, if it’s a two-spring system, is now carrying double the torsion load, which shortens its life dramatically.
- A visible gap in the spring. If you look at the spring above the closed door and see a clean break with a gap between the coils, that’s the failure. It’s usually a separation of about an inch, right at the point where the coil has fatigued. This is something we photograph on every visit; Clause 4 of The Haven Standard is why you see the failed part before anyone quotes a replacement.
- Cables hanging loose or unwound on the drums. When the spring lets go, the lift cables at the sides of the door lose tension and can go slack, jump the drum, or unwind. You may see a coil of cable drooping near the top of the door track. It’s a secondary symptom that confirms the spring failed.
- The door is suddenly heavy to lift by hand. In a normal, balanced setup, you should be able to lift the door manually to about waist height with one hand. After a spring breaks, the door may be brutally heavy. Don’t try to force it; the opener’s manual release cord is the only part you should pull, and only to confirm the door won’t move. If it’s heavy, the spring is done.
BeforeAfterReplacement Cost & What’s Included
Clopay torsion spring replacement in Dallas lands between $180 and $340 installed. The lower end covers a single spring on a lighter door, typically a single-wide like a Clopay Classic 8×7 that takes a 0.207-inch wire spring. The upper end covers heavier doors, two-spring systems, or springs with higher cycle ratings. When we replace one spring, we quote both springs in a two-spring system; it’s not an upsell. A door with two springs that loses one has the other running at a torsional overload and it fails soon after. Replacing both at once gives you a matched, balanced set, a single warranty, and one visit instead of two.
Every quote is a flat, written price and a written scope delivered before any work starts, per Clause 1 of The Haven Standard. You’ll know the specific part number or spec, the labor, and the total before we open the tool bag. The price quoted is the price you pay. The work carries our 365-Day Done Right Promise: if it’s not right, we make it right. You’ll also receive a documented photo record of the failed spring and the completed installation on every visit.
DIY or Call Us?
Torsion springs are under extreme tension; even a partly wound spring stores enough energy to break a hand or a face if it lets go while you’re working. We don’t give step-by-step instructions for winding or unwinding torsion springs, and neither should anyone else. What a homeowner can safely do is inspect: look at the spring for a visible gap, check whether the door is heavy, and note the number of coils, the wire thickness if you have a caliper, and any colored paint on the spring cone. That information helps us quote more accurately over the phone.
What you shouldn’t do is try to replace the spring yourself. The winding and unwinding procedure requires the right bars, the right technique, and the right respect for the stored energy. The spring is wound, the drums are under load, and a stripped winding cone can snap back in an instant. Call us at (469) 460-9039 and we’ll send a background-checked, uniformed technician with the springs on the truck. We’ll measure, quote a flat price, and get the door working the same visit in most cases.
FAQs
Clopay torsion springs are typically rated for about 10,000 cycles, which translates to seven to ten years of normal use for most Dallas homeowners, but the Texas heat and humidity will reduce that number if the spring is on an uninsulated or poorly ventilated garage. Dallas springs that face the afternoon sun in a west-facing garage tend to fail sooner. We log every spring replacement we do, so call (469) 460-9039 and we can give you a real-world read on what we’re seeing in your neighborhood.
No. A broken torsion spring cannot be repaired, only replaced. The break is a fatigue fracture through the wire, and there’s no safe or effective way to rejoin it. We replace with a new spring matched to the door’s weight and cycle rating, and we’ll photograph the old one so you can see the break for yourself.
Most Clopay torsion spring replacements in Dallas take 45 to 90 minutes on site, start to finish. The time goes to unwinding any remnants safely, removing the old spring and cones, fitting the new spring, winding it to spec, checking the balance with the door disconnected, and running the door through a full cycle to confirm it’s smooth. We’ll text you an on-the-way update before the technician arrives so you’re not guessing.
Yes. Our trucks carry a full range of torsion springs in the sizes that cover most Clopay residential doors in the Dallas area, including the common 1-3/4″ and 2″ inside diameters in both wind directions. If your door takes a spring we don’t have on the truck, we’ll source it and return the same day in almost every case. Call (469) 460-9039 and we’ll tell you over the phone what we’re likely to need.
Call for a Flat, Written Price on Clopay Torsion Spring Replacement in Dallas
If your Clopay spring broke, you already know the sound and the sudden inability to get the door open. The next step is a flat, written quote, and that’s exactly how this works. Call (469) 460-9039 and a live person answers, 24/7, including holidays. We’ll schedule a visit, the technician will measure and photograph the failed spring, and you’ll get a written price and scope before any work begins. That’s Clause 1, and it’s how we’ve done every job since 2015. If you’re already holding a competing written estimate, bring it in; our Free Second Opinion means we’ll evaluate it line by line and tell you if it’s fair. No coupon, no code, no fine print.
Written by Marcus Deller, Owner & Lead Technician, Servo Garage Doors Dallas at Servo Garage Doors Dallas, serving Dallas and nearby areas.